DIN EN 2665-003-1999 航空航天系列.额定电流为20A至50A的的三极的温度补偿电路断路保护器.第003部分:米制螺纹端子
时间:2024-05-13 18:14:35 来源: 标准资料网 作者：标准资料网 阅读：9166
【英文标准名称】:Aerospaceseries-Circuitbreakers,three-pole,temperaturecompensated,ratedcurrents20Ato50A-Part003:Metricthreadterminals;productstandard;GermanversionEN2665-003:1999
【原文标准名称】:航空航天系列.额定电流为20A至50A的的三极的温度补偿电路断路保护器.第003部分:米制螺纹端子
【标准号】:DINEN2665-003-1999
【标准状态】:现行
【国别】:德国
【发布日期】:1999-08
【实施或试行日期】:
【发布单位】:德国标准化学会(DE-DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:额定电流;三极;米制螺纹;飞行器部件;名称与符号;飞行器系统;作标记;航天运输;航空航天运输;电气保护设备;多语种的;断路器;产品标准;电气工程;航空运输
【英文主题词】:Aerospacetransport;Airtransport;Aircraftcomponents;Circuit-breakers;Connections;Currents;Designations;Dimensions;Electricalengineering;Electricalpropertiesandphenomena;Electricalprotectionequipment;Electricalsystems;Environmentalcondition;Explosion-proof;Marking;Mass;Mechanicalproperties;Metricscrewthreads;Multilingual;Productstandards;Properties;Pulloperation;Pushoperation;Pushbuttons;Ratedcurrent;Spacetransport;Specification(approval);Switches;Switchgear;Temperature;Temperature-compensated;Threadfasteners;Three-pole;Tri-polecircuit-breakers;UNCthreadfasteners;Weights
【摘要】:
【中国标准分类号】:V27
【国际标准分类号】:49_060
【页数】:9P.;A4
【正文语种】:德语
【英文标准名称】:Analysisofsoaps.Quantitativetestmethods.Methodfordeterminationofunsaponifiable,unsaponified,andunsaponifiedsaponifiablemattercontents
【原文标准名称】:肥皂的分析.肥皂和肥皂粉的分析方法.第2部分:定量试验方法.第5节:不可皂化物质、未皂化物质和未皂化的可皂化物质含量的测定方法
【标准号】:BS1715Sec.2.5-1989
【标准状态】:作废
【国别】:英国
【发布日期】:1989-07-31
【实施或试行日期】:
【发布单位】:英国标准学会(BSI)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:试验条件;肥皂;含量测定;清洗材料;可皂化物测定;非皂化物测定;表面活性剂;化学分析和试验;溶剂萃取方法;商业的;容量分析
【英文主题词】:
【摘要】:
【中国标准分类号】:Y43
【国际标准分类号】:
【页数】:4P;A4
【正文语种】:英语
Product Code:SAE AS1132
Title:Bolts, Screws and Nuts - External Wrenching Unj Thread, Inch Series - Design Standard
Issuing Committee:E-25 General Standards For Aerospace And Propulsion Systems
Scope: The scope of this document is to define the following dimensional requirements for hexagon and double hexagon head bolts and nuts having a minimum tensile strength ranging up to 220 ksi. a. Head dimensions (see 3.1); b. shank dimensions (see 3.2); c. geometric control (see 3.3); d. surface texture (see 3.4); and e. dimensions for nuts (see Section 4). For design calculations the MIL-S-8879 coarse threads, UNJC, shall be used for 0.164 size and smaller and fine threads, UNJF, for larger sizes. For particulars of thread runout and lead threds for bolts, see AS3062. To establish design requirements for bolts, screws and nuts in the UNJ thread inch series primarily for use on propulsion systems. As defined by the Federal Cataloging System, thread sizes less than 0.190 are referred to as screws and larger are referred to as bolts. For the purpose of this document, the term bolt will be used for all sizes.ger are referred to as bolts. For the purpose of this document, the term bolt will be used for all sizes.ger are referred to as bolts. For the purpose of this document, the term bolt will be used for all sizes.ger are referred to as bolts. For the purpose of this document, the term bolt will be used for all sizes.